![]() ![]() Replace cover and turn it one-quarter turn to secure. If your timer has a slotted button-style cover: turn the cover one-quarter turn with a coin or screwdriver.Replace cover by positioning tabs into slots and sliding cover in place. If your timer has a slide-style cover: slide cover off in direction of arrows.Remove the battery cover located on the back side of the timer. To change back, press and hold down Start/Stop button until beep sounds. Press and hold down Start/Stop button until beep sounds, about 3 seconds.(Be sure time of day has been programmed into clock). To alternate between these formats, follow these steps. Some of our Timers offer both 12 (am/pm) and 24 (military) hour time formats. How do I change the display from military time? If error is made in setting clock, simply hold CLOCK button down until digits flash in display and start over. Press CLOCK button to activate clock with programmed time.Set seconds if desired in same manner using the SEC or S button. Press MIN or M button to advance to correct minutes.Press HR or H button to advance to the correct hour of day.Bend West Bend Electronic Stopwatch/Timer West Bend 40053 Triple Timer with Clock. Press CLOCK button down for about 5 seconds or until digits flash in display. West Bend 40055 Single Channel Timer With Clock and Stopwatch NEW.My timer has a clock function, how do I set it? Loudness of timer is preset and cannot be changed. To advance time without beeps, hold button down until desired time is reached. The beeping will occur every time the button is pushed. Can I set my timer without having it beep every time I push the button? ![]() The majority of our times use AAA battery(s) - if your timer is older and uses a button type battery, it is a G-13 button cell battery. To clear timer, press START/STOP/MEMORY button, then press CLEAR button to reset display to zero.Timers What kind of battery does my timer use? To restart same timing period, press START/STOP/MEMORY button once again. To stop timing function before time expires, press correct timer channel button, then press START/STOP/MEMORY button once. TO STOP/RESTART or CLEAR COUNT DOWN TIMERS Flashing channel symbols indicate other timer channels are in operation. 1 0597 Manual (2 pages) Brand: Tjernlund Category: Timer Size: 0.05 MB. Solid channel symbol indicates the count down time of channel being displayed. Tjernlund 950-0453 PAI-T TIMER-CLOCK KIT 8504045 REV. When using all timer channels, simply press the channel button to note count down time remaining. All 3 timer channels can be used at the same time. Press CLEAR button to reset display to zero.įollow same procedure above for programming the other timer channels. If not turned off, alarm will automatically turn off in 1 minute to extend battery life, however, count up timer continues to operate until START/STOP/MEMORY button is pressed. Press START/STOP/MEMORY button to turn alarm off and stop count up timer. Time1 has 1 repetitive beep, Time2 has 2 repetitive beeps and Time3 has 3 repetitive 2 beeps. Each timing channel has it own distinctive alarm. When time expires, alarm will sound and timer will begin to count up in seconds. Time will count down in 1 second intervals. Press START/STOP/MEMORY button to start timer. If error is made in programming, press CLEAR button to zero display, then reprogram time as explained above. The numbers can be fast forwarded by holding individual buttons down for 3 seconds. Press individual HOUR, MINUTE, or SECOND buttons to program desired time. The selected channel symbol will appear in display (T1, T2, or T3). Press Time1, Time2 or Time3 button for desired timer channel. If timers are operating, respective T1, T2 or T3 symbols will flash in display. You can check clock time at any time by simply pressing CLOCK button. Seconds will continue to count in the clock mode. If error is made when programming clock, simply press respective HOUR or MINUTE buttons until correct digits appear. To fast forward minutes, hold button down. Press MINUTE button to advance to correct minutes. ![]() Holding down the HOUR button switches between AM/PM modes in 12-hour intervals. The AM or PM indicator will appear in display. Press HOUR button to advance to correct hour. Press CLOCK button down for about 5 seconds until digits flash in display. TO STOP/RESTART or CLEAR COUNT DOWN TIMERS.HELPFUL HINTS ON USING TIMER/CLOCK/STOPWATCH. ![]() Intermatic ST01 Installation And User Manual Installation and user manual (2 pages) Viessmann VITODENS 050-W Installation And Service Instructions Manual Installation and service instructions manual (88 pages) CAPITAL SPORTS Timeter 2. West Bend 40053 CLOCK/TRIPLE ELECTRONIC TIMER - Use Manual - Use Guide PDF. West Bend ELECTRONIC TRIPLE TIMER/CLOCK Timer: Frequently-viewed manuals. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |